I own the Sovol SV06, it was my first printer but it was also the cheapest option for me ($169 IIRC). The Sovol has given me two problems in the entire time I used it:

1. When it came in, the extruder was jammed. Wouldn’t print or extrude any filament for some reason. Followed a 2 minute video on Sovol’s Amazon page to resolve it (although it did involve disassembling the hotend).

2. The extruder decided to encase itself in plastic one day when I printed something on it. That was a bitch and a half to clean, had to take a heat gun to it to soften the plastic then scrape it off without burning myself. My best guess is it was caused by me forgetting to run bed leveling after moving the printer a bit, hasn’t happened again.

Other than those two times it just works every time I need it. It was sitting dormant for ~3 months and I just kicked off a print yesterday, no problems. Fired right up and everything printed perfectly.

With that said, is it €239 of “Just works”? Probably not. I immediately couldn’t do some prints I planned because of the build volume (although all three of your options have the same build volume). So I’m already considering upgrading to an SV06 Plus. So check some of what you want to print that it’ll fit in 220x220x250.

I did some research on your other options and as far as I can tell, the main difference between them and the Sovol is the all metal hotend and print speed.

Sovol SV06 has an all-metal hotend so you can print high temperature filaments (PETG/TPE/CFN/etc) without worry (does require a harder nozzle most likely though). The other two seem to have some metal but are not fully metal, so if you want to hop into the more exotic materials you’ll have to upgrade those.

Second is speed, my SV06 prints at 80 mm/s. It is slow. Smallest prints take around 2-3 hours. My current print will be done after 24 hours. This is fine for me as most of my prints need complex geometry, so I’d rather it take longer and be accurate than run it too fast. The others claim a max speed of 250mm/s which would be a bit over 3x faster than the Sovol. If they can actually print at that speed without looking awful, that’s a pretty big upgrade time-wise.

If you need exotic filaments and don’t want to upgrade the hotend yourself for it then consider the Sovol. Other than that, the price in your region makes it not an option in my opinion. The Sovol just is a budget printer, only makes sense at budget prices. The Kobra and Ended you mentioned look very similar other than that, they both have auto bed leveling (a must have), same build size, very similar designs. Personally I’d lean towards the Ender, just for the community support. But do some research and see how many community member posts you see online resolved with the two. They seem to be functionally identical to me otherwise (just looking at a spec sheet, I do not have irl experience with either of these printers)

Owning a ghost gun is a crime, right?

(Ignoring the fact that “ghost gun” is a meaningless and intentionally emotionally charged term)

In New York, yes. In the vast majority of the US, no. It’s illegal to file the serial number off an existing firearm, but 100% legal in most states to manufacture your own unserialized firearms for personal use. Just cannot be sold/transferred.

I’d note the article you linked says nothing about how many of those are actually 3D printed, it is infinitely easier to deface the serial number on an existing firearm than it is to 3D print one.

It was a bug in that version of the distro IIRC, trying to install Steam would instead try to install the SteamOS desktop environment (or something along those lines). It has since been fixed to actually install the Steam client.

Obviously it was a bit silly he typed “Yes, do as I say” after seeing the message, but he was also literally following exactly what all the online guides said to do (other than the “Yes do as I say” part). Luckily it’s fixed now but I do think it was a really good demonstration of what the video wanted to see: “What might the average non-techie gamer face using Linux?”

Interesting, I know personally one of my concerns with self-hosting an individual Lemmy instance (after losing my first account to the Vlemmy.net shutdown) was the threat of being held legally responsible for things cached on the server. Say someone uploads something illegal and my server caches it. Seeing it as an option to turn that off is nice, and for an instance only meant to be used by one person I’d imagine caching won’t have a huge impact on load times

That explains a lot, then. When I was on Vlemmy before it was deleted “All” seemed a lot more populated, now I moved to a smaller instance and it seems a lot more repetitive.

It’s a shame it works that way since everyone says the “ideal” is a ton of small instances rather than big ones.

Thanks for the clarification!

Until someone subscribes, it doesn’t exist locally and posts don’t start to flow unless there is a subscriber.

So does this mean that if I’m browsing “All” I’m not actually seeing “All” but “All from the communities/instances members of my instance subscribe to”?