there should be positive pressure in all parts of hotend
This is where the issue lies.
You know those old school, piston style squirt guns?
These work similar to a normal 3d printing setup, the water in the tube is the unmelted filament, the nozzle is the nozzle, and the water spraying out is the extruded filament. This works because the water (unmelted filament) is being pushed through a hole smaller than it’s own diameter, creating the positive pressure you mentioned.
If I remove the nozzle, such that the opening is the same size as the tube, or even widen the nozzle so the opening is wider, there’s no way for any pressure to build up, and the water/filament won’t be propelled/ “extruded”, it will simply pour out the end as if pouring out a cup of water (or hand feeding filament through a tube). It doesn’t matter how fast I pump the water gun, or extrude the filament, as long as there isn’t anything restricting the flow, there’s no way to build up pressure.
All of this to say, of course there’s something that makes it possible because we’ve got a video of it. But there’s more at work than simply, “feed more filament than is able to flow”, because as the video explains, the nozzle is wider than the filament and thus not restricting the flow.
My guess is either it is not a typical, hollow nozzle; there may be some kind of baffling for lack of a better term that disrupts the flow of the filament, pushing it to the edges of the nozzle. removedty sketch of what I’m describing:
Either this or at the beginning of the print the nozzle stays in place and extrudes in one spot until enough has built up for it to start moving. I’m leaning more towards the blocking in the nozzle though, that would creat the positive pressure inside the hotend like the printer is used to.
Interesting comparison with water gun, but that would be equivalent of extruding in the air (even then I see it possible if the nozzle is not way too big). Think about connecting water pipe to a bigger diameter pipe. Water would fill the whole volume and it would just move slower if flow is laminar. There is also filament infront of the nozzle while printing so that should provide resistance (plus friction in the nozzle) to allow pressure build up. Nozzle shape might be important here, but I guess they just drilled 2.4 mm hole all the way through.
I obviously don’t know much about this nozzle, I’m not trying to teach anyone, I’m just having fun brainstorming and hopefully learning something new
I obviously don’t know much about this nozzle, I’m not trying to teach anyone, I’m just having fun brainstorming and hopefully learning something new
Exactly what I’m doing! Haha.
My problem with the “water into a larger diameter pipe” idea is that, while the filament is melted, it isn’t a free flowing liquid that expands quickly to fill it’s container; I’m trying to picture the balancing act that would be required to get the filament to expand by pushing against the build plate/ previous nozzle, but I can only see it ending in a nasty clog.
You’re probably right and it’s likely much more simple than I’m making it out to be. I still like my idea of a baffled nozzle, though. Haha
This is where the issue lies.
You know those old school, piston style squirt guns?
These work similar to a normal 3d printing setup, the water in the tube is the unmelted filament, the nozzle is the nozzle, and the water spraying out is the extruded filament. This works because the water (unmelted filament) is being pushed through a hole smaller than it’s own diameter, creating the positive pressure you mentioned.
If I remove the nozzle, such that the opening is the same size as the tube, or even widen the nozzle so the opening is wider, there’s no way for any pressure to build up, and the water/filament won’t be propelled/ “extruded”, it will simply pour out the end as if pouring out a cup of water (or hand feeding filament through a tube). It doesn’t matter how fast I pump the water gun, or extrude the filament, as long as there isn’t anything restricting the flow, there’s no way to build up pressure.
All of this to say, of course there’s something that makes it possible because we’ve got a video of it. But there’s more at work than simply, “feed more filament than is able to flow”, because as the video explains, the nozzle is wider than the filament and thus not restricting the flow.
My guess is either it is not a typical, hollow nozzle; there may be some kind of baffling for lack of a better term that disrupts the flow of the filament, pushing it to the edges of the nozzle. removedty sketch of what I’m describing:
Either this or at the beginning of the print the nozzle stays in place and extrudes in one spot until enough has built up for it to start moving. I’m leaning more towards the blocking in the nozzle though, that would creat the positive pressure inside the hotend like the printer is used to.
Interesting comparison with water gun, but that would be equivalent of extruding in the air (even then I see it possible if the nozzle is not way too big). Think about connecting water pipe to a bigger diameter pipe. Water would fill the whole volume and it would just move slower if flow is laminar. There is also filament infront of the nozzle while printing so that should provide resistance (plus friction in the nozzle) to allow pressure build up. Nozzle shape might be important here, but I guess they just drilled 2.4 mm hole all the way through.
I obviously don’t know much about this nozzle, I’m not trying to teach anyone, I’m just having fun brainstorming and hopefully learning something new
Exactly what I’m doing! Haha.
My problem with the “water into a larger diameter pipe” idea is that, while the filament is melted, it isn’t a free flowing liquid that expands quickly to fill it’s container; I’m trying to picture the balancing act that would be required to get the filament to expand by pushing against the build plate/ previous nozzle, but I can only see it ending in a nasty clog.
You’re probably right and it’s likely much more simple than I’m making it out to be. I still like my idea of a baffled nozzle, though. Haha